• View and Download Canon PIXMA MP499 manual online. Obtaining Network Key (MAC). PIXMA MP499 Printer pdf manual download.
• Download the latest driver, software, firmware, manual and wireless setup for your Canon PIXMA MG2900 Inkjet Photo All-In-One Printer Series. This is pdutility website to download drivers free of cost.

• Canon Pixma Mp495 Series User Manual (mac) Guide
• Canon Pixma Mp495 Installer

Canon PIXMA MP495 Driver & Software Installations. Manual instruction to install Canon PIXMA MP495 Driver. As if you are about to use the printer, you have to set up the printer driver properly with all these steps below on your Windows operating system.

Download drivers, software, firmware and manuals and get access to online technical support resources and troubleshooting

Please select your PIXMA printer or all-in-one below in order to access the latest downloads including software, manuals, drivers or firmware. You can also view our Frequently Asked Questions (FAQs) and important announcements regarding your PIXMA product.

Once on your product page please use the tabs to navigate between the different content types.

Contact Us

Contact us for telephone or E-mail support

Canon ID

Register your product and manage your Canon ID account

Repair

Locate a repair centre and find other useful information regarding our repair process

• Pixma Printer Drivers & Software Downloads

Have Your Say

WPS Connection Method

Before we start, there are some conditions that must be met in order to use the WPS push button method:

• The access point must have a physical WPS push button available. Please check with your device’s user guide for details. If the WPS push button is not available please use the instructions in the Standard Connection Method section.
• Your network must be using the WPA (Wi-Fi Protected Access) or WPA2 security protocol. Most WPS enabled access points use this protocol.

Step 1

Make sure that the printer is turned on.

If the power is on, the LED (Light Emitting Diode) is lit as shown in the illustration below.

1. Press and hold the [Maintenance] button (A) on the printer for approximately 5 seconds.

2. Make sure that the LED flashes as shown in the illustration below.

Step 2

1. Press the [Fit to Page] button (A).

2. Make sure that the LED flashes as shown in the illustration above, then press the [WPS] button on your access point within 2 minutes.

For exact details regarding pressing the WPS button, please refer to the access point manual.

The (blue) Wi-Fi lamp on the printer will flash while searching for, or connecting to the access point.

3. When wireless connection is complete, the LED lights up for about 3 seconds, then changes to '1' as shown in the illustration below. Make sure that the (blue) Wi-Fi lamp on the printer is also lit.

If any of the following error codes are displayed on the LED (alternately flashing between the letter “E” and then a “Number” followed by another “Number”), please press the [Black] or [Colour] button to dismiss the error, and then repeat steps 1 and 2.

Specific error details:

Error E, 2, 1.

This error appears when wireless connection setup was not completed within 2 minutes after pressing the WPS button.

• Is the access point turned on? If the access point is already turned on, turn it off, and then turn it back on.

Error E, 2, 3.

Canon Pixma Mp495 Series User Manual (mac) Guide

This error appears when multiple WPS access points are detected. Please wait for a while, then configure WPS settings again.

If you have more than one access point, press the [WPS] button on only one access point.

Network settings confirmation

To confirm that your printer is successfully connected to your wireless network, you can print out the network settings of your printer:

1. Make sure that your printer is turned on.

Canon Pixma Mp495 Installer

2. Load a sheet of A4 or Letter-sized plain paper.

3. Press the [Maintenance] button (A) repeatedly until the LED displays .

4. Press the [Colour] button or the [Black] button.

When referring to the printout, check that the “Link Status” indicates “Active” and that the SSID - Service Set Identifier (the name of your wireless network) indicates the correct name of your wireless network.

This concludes the WPS setup procedure.

Please now proceed by installing the software to make the most out of your PIXMA MP495.

If you do not have the installation CD that came with your product, please download the manuals and software to continue.

If the WPS wireless setup is still failing after following this guide, please contact us for further assistance.